How I add cum-lube tubes to dildos

Almost any dildo can be given a cum-lube tube. Which makes the toy much more like the real thing.
If you enjoy water sports. And the feeling of being full. Squirting hot water warmed cum-lube, while getting your fuck-holes pounded hard, fast and deep like I do. You will absolutely love converting all your toys.

You do this procedure at your own risk of injury and or death. Power tools and long drill bits can be dangerous tools. I will not be held responsible for any injuries or death incurred by following this process.

Tools & Supplies:
Super glue.
Electric drill with a trigger lock.
Table mounted vice.
Safety glasses, Leather gloves. Do NOT use cloth type gloves. Because they can get grabbed by the high speed drill bit. Causing injury to your hands or worse.
long drill bits of various widths. I use 1/8 and 1/4 inch X 12 to 26 inch long drill bits.
Medical grade hose. It can be silicone, DEHP plastic, soft PVC plastic vinyl, or non-latex rubber hose. Wider then the hole drilled through the toy. I use the oxygen hoses used by hospitals.

Procedure:
Mount the drill into the vice as tight as possible by the handle. Make sure the drill trigger is accessible. Test the drill to make sure it works. The drill has got to be as stable as possible. Because if it moves during the procedure, you run the risk of damaging yourself and or the toy. You do not want the drill bit to exit anywhere on the toy other than where it is intended to exit. The exit point on the toy should as close to its balls or suction cup as possible.
Connect a drill bit that is as long or longer then the toy.
Hold the toy inline with the drill bit with the tip of the bit 2 or 3 inches above the intended exit point. Mark the drill bit with a white pencil at the tip of the toy. Make sure your white mark goes all the way around the bit. You need to be able to clearly see the mark with the drill at maximum speed.
Put on the safety glasses and leather gloves. Lock the drills trigger at full speed. Keep in mind that the longer the drill bit is. The more it will wobble and oscillate. When I preform this procedure. I always hold the drill bit just above the cutting groves to stabilize it. Holding the drill bit while it’s spinning at full speed with one hand. I slide the center point of the toy’s head over the cutting tip of the bit very slowly with my other hand. Soft materials like that sex toys are made of like silicone and soft PVC. Will try to move and spin with the drill bit. This is where I am the most careful. I slide the toy over the drill bit. Using the hand holding the toy to sense that the drill bit stays in the center of the toy. I stop when the white mark is at the tip of the toy’s head. Than I pull the toy back slowly. To allow the hot stringy piece of silicone to exit through the head of the toy. Keeping in mind, that the hotter the drill bit gets. The more it sticks to the toy. I’ve had drill bits break inside the toy because of heat generated by friction.
I slide the toy back and forth over the drill bit 2 or 3 times to remove as much of the sticky silicone cuttings as possible.
The next step is to bend the toy’s bottom as close to a 90 degree angle from its shaft as possible. While continuing to slide the toy over high speed drill bit passed the white mark. I use the hand holding the toy, to sense the drill bits tip is headed straight for my intended exit point. After the drill bits tip exits through the exit point. I unplug or relies the drills trigger to stop it drilling. Next, I put a drop of super glue on the tip of the drill bit. And slide the tip of the tubing I’m using, over the warm tip of the drill bit. After the glue is dry, I coat the hose dish soap. And pull the drill bit back through the toy. And out the toys head until I have 2 or 3 inches of tubing sticking out of the tip of the toy. Cut the tubing from the drill bit. I use the water pressure from my cleanout wand attached to my shower head to remove the dish soap from between the toy and the hose. It is very important to clean out the dish soap for the super glue to stick correctly. After all the soap is out I squeeze the tip of super glue bottle (not those squeeze tubs) in between the hose and the bottom of the toy. Squeeze the bottle until some oozes out the hole and quickly wipe the excess off with a cloth rag. After the super glue dries, I pull on the piece of tubbing sticking out the head of the toy stretching it slightly while squeezing the tip of the super glue bottle between the tube and toy’s hole. I use much less glue here. Than I cut the hose as flush with the toy’s head. The tube will relies its stretch, and slide back inside the head of the toy about a half inch to one inch. Let the super glue dry.

The 1 gallon pump/squirt bottle is a Dawn dish soap container. I use it for blasting Bad-Dragon.com’s cum lube. White and clear.
If you look at the photos I added to this post. You should understand the rest of the process.
If not. Just contact me with any questions you may have.